Materials:
1/3 yd ruffle fabric (you can find the pink I used here)
1/4″ elastic – 1 14″ piece
1/2″ elastic – 2 8″ pieces
ball point needle
Click HERE to download and print pattern pieces.
Directions:
1. Print pattern pieces. Ensure your printer is not set to scale the pattern. Cut pattern pieces out along solid and dashed lines and tape together along dashed lines. Normally a diaper cover could be cut on the fold, but since ruffle fabric is a bit trickier to cut out (I’ll give some specific tips below), we’re going to use a full pattern piece that’s not on the fold.
2. Lay pattern pieces on ruffle fabric and cut out as directed, aligning top of pattern pieces just below point where one ruffle is attached (flip that ruffle up and out of the way while cutting). This will give enough width of non-ruffled fabric to use for the waistband casing.
A couple of other tips to keep in mind when cutting out your pieces:
When cutting the sides and curves of each piece, make sure that the ruffles are always laying flat as they would naturally fall.
When cutting the bottom of each piece, flip the ruffle nearest the bottom up so it does not get in the way of cutting.
A few tips before we start sewing with ruffle fabric:
* Since ruffle fabric is a knit, always use a ballpoint needle.
* Before pinning and sewing ANY seam, always make sure every ruffle is laying flat and in place. Sewing in the direction that the ruffles are laying will help them to stay put while being sewn (example: sew the side seams from the top of the diaper cover towards the bottom).
* Pin, pin, pin! I can’t say that enough, especially on any curved edges, where it’s more difficult to keep the ruffles in place as their sewn.
* Don’t stretch the fabric as it’s sewn. Allow the feed dogs on your machine to gently guide fabric through.
* Sergers work great with ruffle fabric, but I like to sew the seams with a sewing machine first and serge afterwards to give myself the opportunity to unpick any areas where the ruffles might have gotten out of place when sewn. Do what works best for you :).
* Ruffle fabric raw edges will not fray, so if you don’t have a serger, you can just leave the raw edges after they’re stitched – no need to zigzag.
* Since ruffle fabric is a knit, always use a ballpoint needle.
* Before pinning and sewing ANY seam, always make sure every ruffle is laying flat and in place. Sewing in the direction that the ruffles are laying will help them to stay put while being sewn (example: sew the side seams from the top of the diaper cover towards the bottom).
* Pin, pin, pin! I can’t say that enough, especially on any curved edges, where it’s more difficult to keep the ruffles in place as their sewn.
* Don’t stretch the fabric as it’s sewn. Allow the feed dogs on your machine to gently guide fabric through.
* Sergers work great with ruffle fabric, but I like to sew the seams with a sewing machine first and serge afterwards to give myself the opportunity to unpick any areas where the ruffles might have gotten out of place when sewn. Do what works best for you :).
* Ruffle fabric raw edges will not fray, so if you don’t have a serger, you can just leave the raw edges after they’re stitched – no need to zigzag.
3. Pin and stitch front and back pieces together at sides and bottom edges, leaving leg holes open and using a 1/2″ seam allowance. The ruffle nearest the waistband should be flipped upwards toward the top of the diaper cover while sewing the side seams (I didn’t do this, but I’ll explain why you should in a later step). When stitching the bottom seam, you may have to decrease your seam allowance to avoid stitching into a row of ruffles – I only had about a 1/4″ seam allowance on the bottom in this case, but use 1/2″ if you can.
Your ruffles should be laying nice and flat (your top ruffle will be facing upward though, right?).
4. Turn top of diaper cover 3/4″-1″ (depending how much fabric you have before the next row of ruffles) to the wrong side and pin in place, with the first row of ruffle flipped upward and out of the way of the pins.
If you had sewn the side seams with the top row flipped upward, you would not see this at the side seams, which makes it more difficult to sew the waistband casing without catching the top row of ruffles:
5. Stitch close to edge of pinned waistband, forming a casing for elastic, and leaving an opening to insert elastic. Pay special attention to keeping ruffles out of the way of the seam.
6. Pin one leg opening 1/2″ toward wrong side of fabric, using plenty of pins to keep ruffles in place.
7. Stitch close to edge of pinned edge, forming a casing for elastic and leaving an opening to insert elastic. It’s tricky to keep the ruffles perfectly in place as you sew around the curves, so chances are you’ll have a few areas of imperfection where the ruffles got caught up. The good news is that once the elastic is in, no one else will know, so don’t worry a whole lot about it (for the record, it pains me to say that).
8. Repeat steps 6-7 with remaining leg opening.
9. Use a safety pin to insert a 8″ piece (you can adjust the length of elastic based on the size of your baby’s thighs – take off a bit for an extra tiny baby, add a bit for a chubby baby, or if you want the cover to fit longer, you may also want to add a bit extra length) of 1/4″ elastic into casing of one leg opening. Overlap elastic ends 1/2″ and sew together using a zig zag stitch. Repeat with other leg opening and stitch opening of each casing closed.
10. Use a safety pin to insert a 14″ piece (again, adjust the length as needed) of 1/2″ elastic into waistband casing. Overlap ends 1/2″ and sew together using a zig zag stitch. Stitch casing opening closed.
Great work! Your diaper cover is ready to be worn on a cute little behind :).
No comments:
Post a Comment